2019 North Carolina Hazardous Waste Compliance Workshop No. 2 - Greensboro, NC

The 2019 Hazardous Waste Workshops

Join us for the 27th Annual North Carolina Hazardous Waste Compliance Workshop co-sponsored by the North Carolina Manufacturers Alliance (NCMA) and the North Carolina Department of Environmental Quality (DEQ), Division of Waste Management (DWM). Workshop No. 2 will be held in Greensboro, NC on Thursday, May 16, 2019.

Additional Workshops

The 2019 NC Hazardous Waste Workshops will also be offered on the following dates and locations:

May 9, 2019 Workshop No. 1 - Wilmington
Click here to register for the Wilmington Workshop

May 23 2019 Workshop No. 3 - Asheville Holiday Inn - Biltmore West
Click here to register for the Asheville Workshop

May 30, 2019 Workshop No. 4 - Raleigh McKimmon Center
Click here to register for the Raleigh Workshop

November 14, 2019 Workshop No. 5 - Concord -The Speedway Club at Charlotte Motor Speedway

Registration for the Concord Workshop will open in August, 2019

About this Workshop

Generators of hazardous waste are required to train their employees involved with hazardous waste management.

State and federal regulations require hazardous waste generators to train employees involved with hazardous waste management. Facility personnel must complete classroom or on-the-job training to become familiar with proper hazardous waste management and emergency procedures for the wastes handled at the facility. In addition facility personnel must take part in an annual review of their initial training.

Now you can learn first-hand what regulators from the North Carolina Division of Waste Management expect from hazardous waste generators and treatment, storage and disposal facilities.

The Workshop is designed for facility personnel with hazardous waste duties ranging from environmental managers and coordinators to on-site hazardous waste handlers.

NC hazardous waste leadership will provide insights into policy and initiatives that affect your business. Compliance personnel will present all aspects of safe waste handling practices required for regulatory compliance. You will learn what inspectors look for at your facility through a full-scale inspection exercise. Technical support staff will discuss and interpret hazardous waste regulations as they apply to your business. Waste minimization and enforcement will be reviewed.

The workshop includes plenty of time for questions during each presentation as well as during breaks and lunch. Attendees with specific questions prior to the workshop can also submit those questions to NCMA. NCMA will then provide the questions to DWM staff anonymously so that they can address the questions during the workshop.

Agenda

7:30 AM - Registration
8:00 AM - Introductions
8:15 AM - New & Proposed Rules
9:00 AM - BREAK
9:10 AM - Waste Identification Part 1
10:05 AM - BREAK
10:15 AM - Waste Identification Part 2
11:10 AM - BREAK
11:20 AM - Enforcement
11:50 PM - LUNCH
12:50 PM - Waste Minimization
1:20 PM - BREAK
1:30 PM - UNIVERAL WASTE / USED OIL / E-WASTE
2:10 PM - Inspection - Paperwork
3:10 PM - BREAK
3:20 PM - Inspection - Walkthrough
4:00 PM - Intro to Chemist & Sampling Plan Development

Lunch & Breaks

This all day event includes frequent breaks and a full buffet lunch catered by Coliseum Caterers.

Cost

Standard Registration - $245

NCMA Member Registration - $210

Late Registration (After April 30, 2019) - $295

Presenters

The Workshop will be presented by the staff of the Hazardous Waste Section of the North Carolina Division of Waste Management.

Presenters include: Brent Burch, Heather Goldman, Jenny Patterson, Andrew Martin, Don Burke, Jeff Menzel, Richard Concepción Ernest Lawrence, Rose Pruitt, Autumn Romanski and other regional representatives.

Additional Information

For Additional Information Contact: Donna Pittman at donna.pittman@myncma.org or 919-834-9459